Beginner's Plumbing: The Essentials for Bathtub Installation
Beginner's Plumbing: The Essentials for Bathtub Installation
Blog Article
On this page below you will find a lot of helpful resources involving How to Install a Bathtub.
Installing a bath tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and also sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably difficult project. If the old bathtub is readily available, the task can relocate rapidly; if you need to open a wall surface to get rid of the old tub as well as place the new tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old tub and also set in the brand-new one. See to it you have certified yourself for the task and also fit attempting it. Rather than working with a specialist to take over a halfway-completed job, it is far better to take into consideration using one before you start. Opportunities are you might require an expert plumber to make tube links.
This article will help you set up a brand-new bath tub in your bathroom if you have already bought a new bathtub and also do not require to alter the plan of your previous water system pipes.
Your devices and also material checklist need to comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, turn on the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted gain access to that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a cloth ready for the remaining water that will originate from the pipelines. When the supply pipelines have been eliminated, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming throughout this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the faucet as well as the sink. Secure the tap in position with the manufacturer offered backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet adapters. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of the two wood boards under its feet, position the bath tub in the called for setting. The wooden boards are valuable in uniformly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four little points.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the tub until the level reviews degree.
To install faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the supply of water and also check all joints as well as brand-new pipework for leaks as well as tighten them if required. Load the bath tub and likewise inspect the overflow electrical outlet and the normal electrical outlet for leaks.
Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the bathtub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its final setting.
Getting ready for the Setup
First of all, the supporting frame provided with the bathroom must be fitted (if needed) according to the manufacturer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps device to avoid strain on the bath tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should currently be ready to be suited its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, triggering the water to pass through the wall surface in between the bathroom and the tiling, resulting in difficulties with dampness and possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are offered in tubes as well as cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealer can break fairly very early if you do not think about this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly readily available on the market. It is recommended to fit the floor tiles using waterproof or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading up on Tools You Need to Install a New Bathtub ? Place a remark directly below. We would be pleased to see your insights about this write up. Hoping that you come back again soon. Are you aware of somebody else who is curious about A Step-by-Step Guide to Installing a Bathtub? Why not share it. We value reading our article about Installing A Bathtub.
Call us now! Report this page